Designed for use with the Micro Plus, Envision One, and Vida families of 3D printers, the EnvisionTEC Power Protection System (PPS) DLP is ensures that voltage fluctuations and power outages don’t disrupt the 3D printing process. More than just a battery backup system, the PPS DLP conditions or cleans the power supply from noise and other issues that may interfere with high-value 3D print jobs, where a consistent supply of energy is crucial.
Click here to learn more about how a PPS is different from a UPS and why you need one.
Region
North America
Recommended 3D Printers
Micro Plus and Vida Families
Power Rating VA/Watts
250/200
Inverter Waveform
Low distortion sine wave
Transfer Time
7 ms. Typical
Frequency
60 Hz.
BTU/Hr.
120
T.H.D. Max. w/100% Resistive Load
<4% on battery
On Line Efficiency w/o Charger
86%
Input Voltage
120
Input Current
2.4 Amps
Output Voltage
120
Output Current VA/Watts
2.0/1.6 Amps
Input Voltage Range w/o Using Battery
85 – 156 volts
Output Regulation (mains)
+/- 10%
Output Regulation (on battery)
+/- 5%
Backup Time (full load)
>5 minutes
Entwickelt durch eines der erfahrendsten Teams von Ingenieuren im 3D-Druck, bietet die EnvisionOne cDLM eine beeindruckende Baufeldgröße, dank fortschrittlichster 3D-Druck Technologie. Somit ist ein großes Baufeld, hohe Druckgeschwindigkeit und eine leichte Bedienung der Schlüssel für einen der innovativsten 3D-Drucker des Marktes.
Baufeldgröße
180 x 101 x 175 mm (7.09 x 3.98 x 6.9 in.)
Baugeschwindigkeit
Bis zu 45 mm/Stunde, materialabhängig
Primärmarkt
Dank der EnvisionOne cDLM werden Sie vom Anfänger zum Experten. Sie ist der einzige, professionelle 3D-Drucker, der eine durchgehende Lösung liefert – inkusive der Optimierung von Design-Parametern. Somit ist ein präziser Druck, trotz minimaler Stützstrukturen möglich.
Baufeldgröße
180 x 101 x 85 mm (7.09 x 3.98 x 3.35 in.)
Baugeschwindigkeit
Bis zu 45 mm/Stunde, materialabhängig
Primärmarkt
Die Vida HD cDLM ist ein kontinuierlicher 3D-Hochgeschwindigkeitsdrucker für Schmuck-, Dental- und allgemeine Fertigungsmärkte. Dieser Drucker ist der zweite, welcher die patentierte kontinuierliche, digitale Drucktechnologie von EnvisionTEC ermöglicht. Dieser bietet eine hohe Auflösung in Kombination mit enormen Baugeschwindigkeiten. Darüber hinaus reduziert die Technologie den Bedarf an Stützstrukturen während des Baues, sodass weniger Endbearbeitung erforderlich ist.
Baufeld
90 x 50 x 100 mm (3.54 x 1.97 x 3.94 in.)
XY Auflösung*
50 µm (0.002 in.)
Primärmarkt
The Micro Plus cDLM’s patented technology allows for incredibly fast build speeds without sacrificing resolution or quality. Using a continuous motion of the build plate in the Z direction, prints can be completed in minutes rather than hours and still maintain 1 µm (0.00004 in.) accuracy in the Z direction.
Bauraum
45 x 28 x 75 mm (1.8 x 1.1 x 2.95 in.)
Pixel Size in X
39.8 µm (0.002 in.)
Primärmarkt